Subaru Forester Owners Forum banner

Search results

1-20 of 476 Results
Advanced Search
  1. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Welcome! I'm glad this project is getting more and more attention / interest. It will surely help others in their searching for solution until it becomes more mainstream. Sent from my E6910 using Tapatalk
  2. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    @murfnamedsmurf sadly, I still land in last place lol. So glad you got through it all, but I'm still going through small testing projects. First off, after determining the shields were done, I decided to downsize to the Arduino pro mini and smaller can bus shields. Different adapters needed, but...
  3. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Yes, I however soldered pins on, the cheap/hard way, instead of waiting for a stacked header order on Amazon. Another possible rush job mistake on my part. Truth be told, I ordered parts, modified them all up, to package up for a final product, etc, etc , never once connecting, testing, learning...
  4. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Thanks for the thought, but I confirmed they are no good by troubleshooting each board individually on pin 10, they wouldn't communicate. I've since purchased some new but different hardware, and successful testing so far. I'll share more details once I've tested more in the car. Sent from my...
  5. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    I used a cut portion of a paper clip for the jumper, nice and tight! Sent from my E6910 using Tapatalk
  6. ('09-'13) 2011 - Lowering SH need of rear upper WRX control arms?

    Suspension and Handling
    I'll second that! I've got STI take offs on my 09, no issues with control arms, other than need adjustable lowers if I want to correct the slight negative camber. Sent from my E6910 using Tapatalk
  7. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Actually if I fully understand, you must interupt the CANBUS wires between the SAS and the rest of the system. Your CanBus shields are not "connected" to each other, rather one simply receives (from the SAS), and the other replaces that info with revised scaling, acting as the replacement SAS...
  8. ('09-'13) Cam timing mark accuracy?

    EJ25 - 2.5L Turbocharged (2004-2013)
    I experienced the same as I recall, the cam marks off just a hair. This diagram put my mind at ease, just count the teeth and all should be good (worked for me, anyways). Sent from my E6910 using Tapatalk
  9. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    I cut the data lines long ago. I was just questioning if the angle sensor would put out info if not receiving any, if that makes sense. I'd have tried this method long ago if I knew it was that simple. I'll report back. Sent from my E6910 using Tapatalk
  10. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    @Hired-Goon In order to receive data from the SAS, can I connect right to it, or do I need to connect to the rest of the system and sift through all the can bus data? (I'm a little apprehensive toward the latter) Also, would the example sketch from DFROBOT do it? Sent from my E6910 using Tapatalk
  11. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    I agree and feel that way often, but the old one was rusted out at the hard lines, and this is the way I went at the time. Honestly though, the quicker ratio is awesome and is well worth it for the feel of the drive. All this work is just to get the light off on the dash [emoji23][emoji1787]...
  12. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    So I'm pretty sure my CANBUS shield(s) are toast, or I have 2 bad Arduino boards or both. I can only get info to transmit from shield to shield sporadically. First, I flipped the input and output can wires in the car, and got info on the serial monitor to appear, but I think I was getting info...
  13. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    @Hired-Goon I've got 2 more questions - Do I have my CANBUS signal wires correct Red - CanH, Blue - CanL? Next, on the original sketch, you identify the boards and pin number at the beginning, but should they both remain "CS", or does one have to be designated "SS" on the chip/slave select...
  14. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Hey @Hired-Goon , I've wanted to get a hold of you for over a year now, but wasn't sure how. So glad you found the conversation and reached out...hope you don't mind me sharing your work here, and I hope I've done it justice. Ive certainly got questions, some of which you addressed above but...
  15. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Doing the math, the 13:1 rack turns lock to lock 880 degrees (got that from Chinyues post mentioned above). A 15:1 rack would become 1015 degrees. A difference of 15%. I'd use that in the sketch. Sent from my E6910 using Tapatalk
  16. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Finally I found the other reference for starting this project: https://forums.nasioc.com › forums Web results 2015 STI Steering Rack 13.1!! Anybody Planning to swap ... - nasioc Member Chinyue post#512 Unfortunately, the picture links are gone :-( Sent from my E6910 using Tapatalk
  17. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    So, inever got the Arduino CANBUS SAS scaler to work, as in the traction control light remains on. My buddy Frank says that we have properly gone over the sketch to review for accuracy, the proper libraries for the CANBUS shields are recognized, and all we can come up with is it's not. The...
  18. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    Apparently I've lost the ability or permission to edit my posts for continuity, so I'll just quote here. These pictures are my version of what the original post down under was about building. PLEASE NOTE - at the time I am positive I made mistakes, such as modifying/ damaging the boards before...
  19. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    How to get this working and goals Sent from my E6910 using Tapatalk
  20. ('09-'13) 2009 - STI Steering Rack Issue

    Suspension and Handling
    My pictures Sent from my E6910 using Tapatalk
1-20 of 476 Results
Top